Fmi V300 Manuel d'utilisateur télécharger pdf

IN-V300-08

V300 SET UP INSTRUCTIONS

FOR ADDITIONAL REFERENCES SEE H431 AND Q431

Before using any Fluid Metering, Inc. product read the following safety instructions

as well as specific product specifications and operating instructions.

Warning! Fire, electrical shock or explosion may occur if used near combustibles

explosive atmosphere, corrosive air, wet environment or submerged in fluid.

Caution! Fire, electrical shock, injury and damage may

occur if not used in accordance with Fluid Metering, Inc.

specifications and operation instructions.

Do not put wet fingers into power outlet of unit.

Do not operate with wet hands.

Do not operate drive assemblies that require a hard mount

(to be bolted down) unless they are mounted per Fluid Metering.

specifications, if not injury may occur and/or damage to unit.

Do not touch any rotating pump or motor components: injury

may occur.

Do not run pump dry, unless designed for that service.

Running dry is harmful to the pump, and will cause excessive

heating due to internal friction.

Check pump rotation and inlet/outlet pump port orientation

before connecting power to pump. If not injury may occur.

When pulling out cords from outlets do not pull cord, grasp

plug to prevent plug damage or electrical shock.

Fluid Metering, Inc. Drive Motors become HOT and can

cause a burn

. DO NOT TOUCH!

Turn off the electrical power before checking pump for any problems.

Connect motor, speed controllers, or any other electrical devices

based on Fluid Metering Inc. specifications. Any unauthorized work

performed on the product by the purchaser or by third parties can

impair product functionality and thereby relieves Fluid Metering, Inc.

of all warranty claims or liability for any misuse that will cause

damage to product and/or injury to the individual.

Power cables and leads should not be bent, pulled or inserted by

excessive force. Otherwise there is a threat of electrical shock or fire.

Replace any inline fuses only with fuse rating as specified by

Fluid Metering, Inc.

When pump/drive is under operation, never point discharge tubing

into face or touch any rotating components of pump. In a power

down thermal overload cut-in condition, unplug or turn off power

to pump. Always allow a cool down period before restarting:

otherwise, injury or damage may occur.

For 30 seconds after power is removed from pump/drive: do not

touch any output terminals. Electrical shock may occur because of

residual voltage.

SAFETY INSTRUCTIONS

Figure 1 Figure 2

1 2 3 4 5 6 7

Résumé du contenu

Page 1 - V300 SET UP INSTRUCTIONS

IN-V300-081V300 SET UP INSTRUCTIONS FOR ADDITIONAL REFERENCES SEE H431 AND Q431Before using any Fluid Metering, Inc. product read the following safety

Page 2 - IN-V300-08

IN-V300-081.0 General DescriptionThe V300 Stroke Rate Controller provides precisionflow control for FMI variable speed "V" Series pumps.The

Page 3

display. The stroke rate is displayed as a percentageof the fastest rate. If you attempt to go beyond theselimits, the display will show three dashe

Page 4

cating you are under the limit. (See Figure 2 for cableconnections)To run the V300 system in 4-20 mA mode, simply turnthe Mode Switch to "4-20 mA

Page 5 - Figure 3

Caution: On power up, the pump will start automatically. Do not turn on the power to the controlmodule unless you are sure that the pump is ready too

Page 6

Page 7 - Figure 4

5.75 146.14.0 101.6V300OUTLINEV300MOUNTING TEMPLATEFigure 4

Commentaires sur ces manuels

Pas de commentaire

Fmi V300 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pompes Fmi V300. FMI V300 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pompes Fmi V300